ISO 9001:2015 Certified · Nashik, India
Margo Rubber Products moulds rotary and static oil seals to your shaft diameter, housing bore and width at its ISO 9001:2015 certified plant in Nashik, India — in AEM, FKM, NBR, EPDM and silicone, to DIN 3760 and ISO 6194 profiles or cut to print. AEM seals go to Mahindra & Mahindra for transmission applications.
02 · SPECIFICATION REFERENCE
Compare service temperature and media resistance before specifying. Figures are indicative ranges for the compound family — confirm against the datasheet for your application.
| Material | Temp range | Chemical / oil resistance | Typical application |
|---|---|---|---|
| AEM (Vamac®) | −40° to +175°C | Excellent — hot oil, heat and ozone together | Automotive transmission and engine seals |
| FKM (Viton®) | −20° to +250°C continuous to 200°C | Excellent — petroleum oils, fuels, solvents | Oil & gas, petrochemical |
| NBR (Nitrile) | −30° to +120°C | Very good — mineral oils, hydraulic fluid | General industrial, automotive |
| EPDM | −40° to +140°C | Poor in oil; excellent in water and steam | Water pumps, brake systems |
| Silicone (VMQ) | −60° to +220°C | Moderate — dry heat, not for fuels | High-temperature static sealing |
Typical values. See our technical disclaimer.
03 · MATERIAL SELECTION
Ethylene acrylic elastomer. Our signature compound for rotary sealing, supplied to Mahindra & Mahindra for transmission applications. Holds compression-set stability where oil, heat and ozone act together.
Fluorocarbon rubber, the first choice for aggressive chemistry and sustained heat. Resists petroleum oils, fuels and many solvents where nitrile is attacked.
Nitrile butadiene rubber, the general-purpose standard for oil sealing. Outstanding resistance to petroleum oils and hydraulic fluids at moderate temperature.
Water, steam and brake fluid service, with excellent weather and ozone resistance. Not for petroleum oils — the commonest mis-specification on a seal.
The widest service range of the eight, for high-temperature static sealing. Biocompatible grades available; we do not hold FDA registration or ISO 13485. Poor abrasion resistance — not for a rotating shaft.
Balanced properties across weather, refrigerants and moderate oil. Flame-retardant grades available. Rarely specified for rotary service.
Abrasion resistance at low cost, for static seals in water and mild service. Not for oil or fuel contact, and rarely specified for rotary service.
The highest resilience of the eight, specified where a seal also has to damp. Not for oil, fuel or sustained heat, and rarely specified for rotary service.
IN THIS CATEGORY
Every seal below is moulded to a customer drawing, a standard profile reference, or a worn sample. Compound, hardness and dimensions are set from your specification; full dimensional data is issued with the quotation.
01
Oil Seals · Made to order
02
Oil Seals · Made to order
03
Oil Seals · Made to order
04
Oil Seals · Made to order
05
Oil Seals · Made to order
06
Oil Seals · Made to order
07
Oil Seals · Made to order
08
Oil Seals · Made to order
09
Oil Seals · Made to order
10
Oil Seals · Made to order
11
Oil Seals · Made to order
12
Oil Seals · Made to order
13
Oil Seals · Made to order
14
Oil Seals · Made to order
15
Oil Seals · Made to order
16
Oil Seals · Made to order
17
Oil Seals · Made to order
18
Oil Seals · Made to order
19
Oil Seals · Made to order
20
Oil Seals · Made to order
21
Oil Seals · Made to order
05 · COMMERCIAL TERMS
Margo produces in bulk against OEM schedules. Tell us the shaft, the bore, the width and the volume and we will quote it. Minimum run is 10,000 pieces per part number, per compound, or quoted against the part where size or complexity sets the economics. Prototype and first-article lots sit outside the minimum and are quoted separately.
Quotation
With feasibility report
48 hrs
Prototype
From an approved drawing
48–72 hrs
Catalogue sizes
Ex-works Nashik, from drawing approval · 2 weeks express
3–4 weeks
Cut-to-print
Tooling lead time quoted per part
3–4 weeks + tooling
Packaging
Bulk or blister on request
Poly bag + card label
06 · ENQUIRIES
Shaft diameter, housing bore, width and the fluid it runs in. That is enough to quote. We reply within one business day, and a quotation with a compound recommendation follows inside 48 hours. No drawing? Send the worn seal.
