Robotic automotive body assembly line
TIER-1 OEM SUPPLIER · DRAWING-MATCHED PRODUCTION

Rubber Components for Automotive OEMs, Manufactured in India

Margo’s largest sector by volume. Moulded rubber components for powertrain, chassis, body and under-bonnet assemblies, produced to your drawing at our ISO 9001:2015 certified plant in Nashik — including AEM, the compound we supply to Mahindra & Mahindra.

Request Automotive Component Specs View Certifications

COMPONENTS WE SUPPLY FOR AUTOMOTIVE

Engineered to Spec, Not to Catalogue

We don’t stock generic parts. Each component is produced against your drawing or an OEM sample — compound, hardness and geometry matched to the mounting position rather than picked from a catalogue.

Bonded rubber silent-block bushes at Margo Rubber Products, Nashik

Bushes & Bushings

Silent-block and AEM insulation bushes for suspension, engine and transmission mounting

  • AEM signature compound
  • Bonded and unbonded variants
  • Bore, OD and durometer to drawing
  • Supplied to Mahindra & Mahindra
Request Specs for Bushes & Bushings

WHERE OUR COMPONENTS ARE USED

Built into vehicles on the line.

Powertrain & transmission

AEM insulation bushes, engine mounts and transmission oil seals rated for sustained under-bonnet heat and oil contact.

Chassis & suspension

Silent-block bushes, shackle and spring eye bushes, and anti-vibration mounts matched to your suspension geometry and load case.

Body & interior

Support pads, glove-box stoppers, footrest mats, C-pillar garnish foam and trim sealing produced against controlled drawings.

Thermal & air management

A/C air-extractor flaps, radiator shroud flaps, hose and cooling-system seals for under-bonnet assemblies.

BUILT FOR AUTOMOTIVE CONDITIONS

Compounds built for under-bonnet reality.

Automotive duty combines heat, oil, vibration and volume. Compound and geometry are selected for the specific mounting position rather than from a generic catalogue.

Heat ageing resistance

AEM holds a −40 °C to +175 °C service range, continuous to about +160 °C, with strong resistance to engine oils and heat ageing, which is why it is our signature automotive compound.

Vibration isolation

Mount geometry and durometer tuned to the resonance frequency of the assembly, not to generic softness. Isolation only begins above about 1.4 times the system natural frequency.

Oil & fluid contact

NBR and AEM compounds selected where sustained contact with engine oils, coolants or transmission fluid is expected.

Volume consistency

Long-run production with batch-level traceability, so the ten-thousandth part matches the first article.

CUSTOM ENGINEERING

We match your vehicle spec, not the other way around.

Margo operates dedicated tooling capability for custom rubber components. Send us your OEM drawing, an existing part, or the equipment make and model — we reverse-engineer and produce to your specification.

  • OEM drawing and sample matching
  • Custom mould tooling in-house
  • Compound selection by application
  • Pre-production sample approval process
  • Long-run production with consistent batch quality
Discuss a Custom Component
Margo production line at the Nashik facility

Nashik, Maharashtra, India

ISO 9001:2015 certified manufacturing facility

QUALITY & CERTIFICATION

Every batch. Every shipment.

Margo Rubber Products holds ISO 9001:2015 certification, certificate 09111526A, issued by Integral Certification Ltd and valid to 21 February 2027. Our quality management system covers incoming raw material inspection, in-process control and outgoing batch documentation.

ISO 9001:2015

Quality management system

Certified quality management covering all production and inspection processes. Certificate 09111526A, Integral Certification Ltd. Documentation available on request.

OEM compliance

Drawing-matched production

Every component produced against a controlled drawing revision. No substitutions without approval.

Batch traceability

Full material traceability

Raw material certificates and batch records retained per shipment. Available to automotive buyers on request.

Request ISO Certificate Request Quality Policy All Certifications

DOMESTIC & EXPORT SUPPLY

Supplying Indian OEMs and export automotive buyers.

Margo supplies automotive components to Indian OEMs and Tier 1 suppliers directly from Nashik, and exports with full documentation to buyers in our active markets.

Components are produced against your controlled drawing revision, with pre-production sample approval before volume release.

Export documentation
Commercial invoice, packing list, certificate of origin
Freight routing
Sea and air freight via established forwarders, ex-works Nashik
Communication
English-language correspondence and technical support
Payment terms
Discussed per order — TT and LC accepted

Nashik → OEM Lines

Direct supply to OEMs and Tier 1 suppliers

  • Domestic OEM supply
  • Tier 1 sub-assembly
  • Aftermarket export
  • First-article and sample approval lots
  • Long-run volume production

Margo Rubber Products holds ISO 9001:2015 certification, certificate 09111526A. We are actively upgrading our quality management system to IATF 16949:2016 and are targeting certification by the end of 2026.

FREQUENTLY ASKED QUESTIONS

Questions from automotive buyers.

GET STARTED

Ready to specify automotive components from the Nashik plant?

Send the controlled drawing, an existing part, or the vehicle make and model, with the mounting position and your volume. Our engineering team responds within 48 hours with a compound and hardness recommendation, dimensional confirmation and a quotation.

Request Automotive Component Specs Call Technical Sales