ISO 9001:2015 Certified · Nashik, India
Margo Rubber Products moulds rubber-to-metal bonded and unbonded anti-vibration mounts at its ISO 9001:2015 certified plant in Nashik, India — bobbin, conical, sandwich and buffer forms in natural rubber, neoprene and NBR. Engineered to your load rating, deflection and mounting geometry, to OEM drawing rather than off the shelf.
Send a Mount Drawing02 · SPECIFICATION REFERENCE
A mount is specified by the static load it carries and the stiffness that load has to sit on, not by dimension alone. Send the supported mass, the number of mounting points, the disturbing frequency and the mounting geometry with the drawing, and we will select and quote it.
| Cylindrical bobbin — male/male | 5–150 kg | 45–60 Shore A | Compressors, small gensets, control panels, fan assemblies |
|---|---|---|---|
| Cylindrical bobbin — male/female | 5–150 kg | 45–60 Shore A | Where one face bolts through and the other threads in |
| Cylindrical bobbin — female/female | 5–150 kg | 45–60 Shore A | Panel and enclosure isolation with studs from both sides |
| Conical / bell mount | 20–400 kg | 50–70 Shore A | Engine and cab mounting where load comes in on more than one axis |
| Plate / sandwich mount | 50–800 kg | 55–75 Shore A | Machine feet, pump and motor bases, heavy static loads |
| Shear / V-mount | 10–250 kg | 45–65 Shore A | Loaded in shear for lower stiffness and better low-frequency isolation |
| Buffer / bumper stopper | Impact duty | 60–80 Shore A | End-stops and travel limiters — absorbs impact, does not isolate |
| Bonded bush / sleeve mount | Per drawing | 50–75 Shore A | Suspension and linkage pivots, torsional and radial duty |
Showing 8 of 8 entries. How a mount is selected: the mount and the mass it carries form a spring-mass system with a natural frequency. Isolation only begins once the disturbing frequency is more than about 1.4 times that natural frequency, and is worth having at a ratio of three or more — which is why a softer mount usually isolates better, and why a mount that is too stiff for its load does nothing at all. Give us the supported mass per mounting point and the running speed of the machine and we will size it. Load and hardness bands are typical for the mount type and are not a specification for a particular part; see our technical disclaimer.
03 · MATERIAL SELECTION
On a mount the compound is chosen for how it behaves under repeated load, not for what it resists chemically. Natural rubber is the default and the right answer most of the time; the others are what you move to when oil, heat or weather rules it out.
Polyisoprene, and the standard anti-vibration compound. The highest resilience and the best fatigue life of the eight, with the lowest dynamic-to-static stiffness ratio — which is the property that decides whether a mount isolates in service as well as it does on paper. Not for oil, fuel or sustained heat.
Polychloroprene. The answer when a mount has to survive weather, ozone and moderate oil at the same time — an exposed machine foot or an under-bonnet mount. Slightly stiffer and less resilient than natural rubber, and worth the trade when the mount is outdoors. Also the family we reach for when flame retardancy is specified.
Nitrile butadiene rubber. Specified where the mount sits in or near petroleum oil or hydraulic fluid, which natural rubber cannot take. Dynamic behaviour is a compromise against natural rubber, so specify it for the oil, not for the isolation.
Styrene butadiene rubber. Abrasion resistance at low cost, blended with natural rubber in buffers and stoppers where the part takes impact rather than isolating a running machine. Not for oil or fuel contact.
Ethylene propylene diene rubber. For mounts that live outdoors or near steam and coolant, with excellent weather and ozone resistance. Higher damping and lower resilience than natural rubber. Not for petroleum oils.
Ethylene acrylic elastomer. Our signature compound, supplied to Mahindra & Mahindra for engine and transmission applications. Specified for a mount that has to hold its properties where oil, heat and ozone act together and neither natural rubber nor nitrile will last.
Fluorocarbon rubber. High cost, high damping loss and low resilience, so it is rarely specified for vibration isolation — it appears here because we mould it, and because a mount that is really a chemical-service block sometimes needs it.
Vinyl methyl silicone, the widest service range of the eight. Poor tear and fatigue resistance, and a bonded mount in silicone tends to fail at the bond line, so it is rarely specified for vibration isolation — use it for a static high-temperature pad rather than a running mount.
04 · IN THIS CATEGORY
Each part below is manufactured to customer drawing or to our standard tooling. Load rating, hardness, insert geometry and bonding are set from your specification, and full dimensional data is issued with the quotation.
01
Anti-Vibration Mounts · Made to order
02
Anti-Vibration Mounts · Made to order
03
Anti-Vibration Mounts · Made to order
04
Anti-Vibration Mounts · Made to order
05
Anti-Vibration Mounts · Made to order
06
Anti-Vibration Mounts · Made to order
07
Anti-Vibration Mounts · Made to order
08
Anti-Vibration Mounts · Made to order
09
Anti-Vibration Mounts · Made to order
10
Anti-Vibration Mounts · Made to order
11
Anti-Vibration Mounts · Made to order
12
Anti-Vibration Mounts · Made to order
13
Anti-Vibration Mounts · Made to order
14
Anti-Vibration Mounts · Made to order
15
Anti-Vibration Mounts · Made to order
16
Anti-Vibration Mounts · Made to order
17
Anti-Vibration Mounts · Made to order
18
Anti-Vibration Mounts · Made to order
19
Anti-Vibration Mounts · Made to order
05 · COMMERCIAL TERMS
Margo produces in bulk against OEM schedules. Send the drawing with the supported load, the mounting geometry and the insert specification, plus the compound and the volume, and we will quote it. Minimum run is 10,000 pieces per part number, per compound, or quoted against the part where size or complexity sets the economics. Prototype and first-article lots sit outside the minimum and are quoted separately.
Quotation
With feasibility report
48 hrs
Prototype
From an approved drawing
48–72 hrs
Existing tooling
Ex-works Nashik · 2 weeks express
3–4 weeks
New tooling
Mould and insert fixture quoted separately
3–4 weeks + tooling
Packaging
Bulk or partitioned carton on request
Poly bag + card label
06 · ENQUIRIES
Send your drawing with the supported load per mount and the mounting geometry, or a sample of the mount you are replacing, together with the insert specification and the volume. Our engineering team responds within 48 hours with a recommended type and hardness, dimensional confirmation and a quotation.
