Centrifugal pumps
Rotary shaft seals, casing gaskets and moulded wear components produced to your drawing, matched to the duty point and the medium.
OEM COMPONENT SUPPLIER · DRAWING-MATCHED PRODUCTION
Rubber Components for Pumps and Valves, Manufactured in India
Precision sealing components that keep fluid-handling systems leak-free — flange gaskets, shaft seals, O-rings and diaphragms moulded to your drawing at our ISO 9001:2015 facility in Nashik, India.
COMPONENTS WE SUPPLY FOR PUMPS & VALVES
Engineered to Spec, Not to Catalogue
We don’t stock generic parts. Each component is produced against your drawing or an OEM sample — compound, hardness and geometry matched to the medium and the duty point rather than picked from a catalogue.
Gaskets
Flange, casing and body gaskets for pump housings and valve bodies
- ASME B16.21, EN 1514-1 and JIS B2404
- EPDM, NBR and FKM
- Moulded and die-cut
- Full material certification
O-Rings
Body, bonnet and seat seals for gate, ball, butterfly and control valves
Bellows & Boots
Protective boots for valve stems, actuator rods and exposed spindles
Bushes & Bushings
Pivot and linkage bushes for valve actuators and pump baseplates
Anti-Vibration Mounts
Bonded mounts for pump skids, motor bases and packaged sets
Extruded Profiles & Cord
O-ring cord and vulcanised joined rings for large-diameter housing joints
WHERE OUR COMPONENTS ARE USED
Built into fluid-handling equipment.
Diaphragm & peristaltic pumps
Moulded diaphragms and extruded silicone tubing, produced against controlled drawing revisions.
Valve bodies & seats
O-rings and seat profiles for gate, ball, butterfly and control valves across process duty. Stem boots for exposed spindles.
Metering & instrumentation
Precision small-bore seals and gaskets for meters, sensors and instrumentation housings.
BUILT FOR PUMPS & VALVES CONDITIONS
Sealing chosen by medium, not by catalogue.
Fluid handling covers everything from potable water to aggressive process chemistry. The compound is selected for the medium in contact and the service temperature, then the geometry is matched to your housing.
Media compatibility
EPDM to +140 °C for water and steam, NBR to +120 °C for oils, FKM to +250 °C for aggressive chemistry. Selection is driven by your medium, not by stock availability. EPDM must not be used in petroleum service.
Dynamic sealing
Rotary lip seals and dynamic O-rings specified for shaft speed and surface finish, not dimension alone. Send the shaft finish with the drawing — it is the most common cause of premature lip-seal failure and it is rarely on the enquiry.
Temperature range
Compounds across the full service envelope: silicone from −60 °C, EPDM from −40 °C, FKM to +250 °C — sub-zero ambient through to sustained high-temperature process duty.
Abrasive slurry
Natural rubber has the best abrasion resistance of the eight compounds we mix, and we mould it to your drawing for slurry-duty seals and wear components. We supply both: components moulded to drawing, and rubber sheet lining for casings, sumps and pipework in the same compounds.
CUSTOM ENGINEERING
We match your pump spec, not the other way around.
Margo operates dedicated tooling capability for custom rubber components. Send us your OEM drawing, an existing part, or the equipment make and model — we reverse-engineer and produce to your specification.
- OEM drawing and sample matching
- Custom mould tooling in-house
- Compound selection by application
- Pre-production sample approval process
- Long-run production with consistent batch quality
Nashik, Maharashtra, India
ISO 9001:2015 certified manufacturing facility
QUALITY & CERTIFICATION
Every batch. Every shipment.
Margo Rubber Products holds ISO 9001:2015 certification, certificate 09111526A, issued by Integral Certification Ltd and valid to 21 February 2027. Our quality management system covers incoming raw material inspection, in-process control and outgoing batch documentation.
ISO 9001:2015
Certified quality management covering all production and inspection processes. Certificate 09111526A, Integral Certification Ltd. Documentation available on request.
OEM compliance
Every component produced against a controlled drawing revision. No substitutions without approval.
Batch traceability
Raw material certificates and batch records retained per shipment. Available to pump and valve buyers on request.
EXPORT SUPPLY
Direct supply from Nashik to pump and valve OEMs.
Margo Rubber Products exports sealing components directly to pump and valve manufacturers across our active markets, with full export documentation managed from Nashik.
Components are produced against your controlled drawing revision, with pre-production sample approval before volume release — and the revision is recorded on the despatch documentation.
- Export documentation
- Commercial invoice, packing list, certificate of origin
- Freight routing
- Sea and air freight via established forwarders, ex-works Nashik
- Communication
- English-language correspondence and technical support
- Payment terms
- Discussed per order — TT and LC accepted
India → Export Markets
Direct OEM supply chain from Nashik, Maharashtra
- Australia
- United Kingdom
- United Arab Emirates
- United States
- Singapore
Buyers are responsible for confirming applicable import duties for their specific order. We supply the certificate of origin and material certificates your customs broker and incoming inspection will ask for. Contact us for documentation support.
FREQUENTLY ASKED QUESTIONS
Questions from pump and valve buyers.
GET STARTED
Ready to specify pump components from the Nashik plant?
Send the drawing, an existing part, or the pump or valve make and model — with the medium, the service temperature and, for a shaft seal, the shaft finish. Our engineering team responds within 48 hours with a compound and hardness recommendation, dimensional confirmation and a quotation.