Custom Rubber Parts Manufactured to Your Drawing. Fifteen Product Lines.
Margo Rubber Products moulds and extrudes eleven lines of precision rubber components at its ISO 9001:2015 certified plant in Nashik, India — sealing, anti-vibration, protection, continuous profile and cellular. Compound, hardness and dimensions set from your drawing or a physical sample.
- 15
- Product Lines
- 200+
- Catalogue SKUs
- 8
- Compounds Mixed In-House
- ISO 9001:2015
- Certified Quality
PRODUCT CATALOGUE
Fifteen Rubber Component Lines, Moulded and Extruded to Drawing
twelve moulded, one continuous-profile extruded, one cellular sponge and foam, and one sheet rubber-lining line. O-rings come in standard AS568, ISO 3601 and metric sizes. Everything else is made to your drawing or sample, with moulds and extrusion dies designed and cut in-house
SealingPRECISION SEALING TO STANDARD SERIES
O-Rings
by the piece
SealingROTARY SHAFT SEALING, LIP TYPE
Oil Seals
by the piece
SealingFLANGE AND PROFILE SEALING
Gaskets
by the piece
SealingRUBBER DIAPHRAGMS, MOULDED TO YOUR STROKE AND PRESSURE
Diaphragms
SealingRECIPROCATING SEALS FOR RODS, PISTONS AND PLUNGERS
Reciprocating Seals
CustomSEALS THE TEST, NOT THE PART
Leak Test Rubber
by the piece
Anti-VibrationISOLATE, DAMPEN, PROTECT
Anti-Vibration Mounts
by the piece
Anti-VibrationPRECISION BORE, ENGINEERED FIT
Bushes & Bushings
by the piece
Anti-VibrationRUBBER BONDED TO METAL IN ONE CURE, NOT GLUED ON AFTER
Bonded Components
ProtectionFLEXIBLE EXPANSION AND PROTECTION
Bellows
by the piece
ProtectionSEALED CABLE AND PANEL ENTRY
Grommets
by the piece
CustomCUSHIONING, STOPPING, PROTECTING
Pads, Stoppers & Caps
by the piece
Continuous Profile & Cellular
ProfilesCONTINUOUS PROFILE, ANY CROSS-SECTION
Extrusion Profiles
by the metre
CellularCELLULAR ELASTOMERS, OPEN AND CLOSED CELL
Sponge & Foam Rubber
sheet, roll or piece
MANUFACTURING CAPACITY
Five Million Components a Month, Installed
Automated presses with closed-loop temperature and pressure control, digital curing ovens with a retrievable cure record per batch, and IoT line monitoring. Current output is 1.5 million a month, so a volume ramp gets press time rather than a queue position.
INSTALLED CAPACITY
5M pcs / month · 30% utilised
- 5M
- Installed Capacity
- 15
- Product Lines
- <1%
- Target Rejection Rate
- 25×
- Capacity Growth
Pieces per month
12 moulded · 1 extruded · 1 cellular · 1 sheet lining
Post-automation
Against the previous works
From Compound to Certified Part, Under One Roof
- 01
Compound formulation
Mixed in-house across eight polymer families. Formulated to the duty cycle — hot oil, ozone under static strain and thermal cycling each take a different mix.
- 02
Tooling
Mould and die designed and cut here from a CAD file, a section drawing or a worn sample. Prototyped to prove geometry before volume release.
- 03
Moulding & extrusion
Compression, transfer and injection moulding, plus continuous-cure extrusion. Automated presses hold cure temperature and pressure closed-loop.
- 04
Laboratory release
First-article dimensional check, then in-process inspection through the run. Every despatch lot released against hardness, dimension and visual criteria.
In-House Capabilities
- In-house rubber compounding
- Mould and die tooling in-house
- Compression, transfer & injection moulding
- Continuous-cure extrusion
- Dimensional inspection to ISO 3302-1
- ODR rheometer cure-curve control
- Reverse engineering from a worn sample
- Batch traceability · APQP and PPAP on request
Need a capability assessment?
Send a drawing or a sample. Our engineers will confirm feasibility, recommend the compound, and quote inside 48 hours.
Talk to an EngineerMATERIAL ENGINEERING
Eight Compounds, Mixed in Our Own Plant
We mix our own compound rather than buying it in, which is why the formulation can be written for your duty cycle instead of pulled off a shelf. Name the fluid, the temperature and the load and we will tell you which of the eight to specify.
AEM
Ethylene Acrylic Elastomer (Vamac)
Our signature compound. Holds flexibility and compression-set stability where oil, heat and ozone all act at once. Supplied to Mahindra & Mahindra for engine and transmission applications.
Key Properties
- Temperature Range
- −40 °C to +175 °C (continuous to 160 °C)
- Hardness Range
- 50–80 Shore A
- Best For
- Heat + Oil
Typical Applications
- 01Insulation bushes
- 02Transmission seals
- 03Under-bonnet O-rings
FKM
Fluoroelastomer (Viton)
The compound for aggressive chemistry and sustained heat. Resists hydrocarbons, acids and solvents that destroy nitrile.
Key Properties
- Temperature Range
- −20 °C to +250 °C (continuous to 200 °C)
- Hardness Range
- 60–90 Shore A
- Best For
- Chemical-Resistant
Typical Applications
- 01Oil & gas seals
- 02Fuel system O-rings
- 03High-temp gaskets
Silicone (VMQ)
Vinyl Methyl Silicone
The widest service range of the eight, and the only family with biocompatible grades. Poor abrasion resistance — not a wear part.
Key Properties
- Temperature Range
- −60 °C to +220 °C
- Hardness Range
- 30–80 Shore A
- Best For
- Temperature Extremes
Typical Applications
- 01Medical tubing
- 02Switchgear gaskets
- 03Insulator covers
EPDM
Ethylene Propylene Diene Monomer
Weather, ozone, steam and hot water. The default for anything that lives outdoors or under static strain in sunlight.
Key Properties
- Temperature Range
- −40 °C to +140 °C
- Hardness Range
- 40–90 Shore A
- Best For
- Weather + Steam
Typical Applications
- 01Weatherseals
- 02HVAC foam strips
- 03Water main sealing rings
NBR
Nitrile Butadiene Rubber
The workhorse for oil contact. Excellent resistance to petroleum oils, fuels and greases, with low gas permeability.
Key Properties
- Temperature Range
- −30 °C to +120 °C
- Hardness Range
- 40–90 Shore A
- Best For
- Oil-Resistant
Typical Applications
- 01Hydraulic seals
- 02Fuel system parts
- 03O-rings
Neoprene (CR)
Polychloroprene
General purpose with balanced properties, and the family we reach for when flame retardancy is specified.
Key Properties
- Temperature Range
- −40 °C to +120 °C
- Hardness Range
- 40–90 Shore A
- Best For
- Flame-Retardant Grades
Typical Applications
- 01Enclosure gaskets
- 02Foam tape
- 03Bonded pads
SBR
Styrene Butadiene Rubber
Abrasion resistance at low cost. Specified where a part wears rather than seals.
Key Properties
- Temperature Range
- −30 °C to +100 °C
- Hardness Range
- 40–90 Shore A
- Best For
- Abrasion-Resistant
Typical Applications
- 01Wear pads
- 02Buffer stops
- 03General mouldings
Natural Rubber
Polyisoprene (NR)
The highest resilience of the eight. Specified for damping, not for oil or heat.
Key Properties
- Temperature Range
- −20 °C to +90 °C
- Hardness Range
- 30–80 Shore A
- Best For
- Damping
Typical Applications
- 01Anti-vibration mounts
- 02Suspension bushes
- 03Footrest mats
INDUSTRIES WE SERVE
Which Line Goes Into Which Industry
The fifteen lines serve eleven sectors. What changes between them is the compound, the tolerance class and the documentation that ships with the part.
AutomotiveInsulation bushes, oil filler caps, radiator shroud flaps and footrest mats for passenger and commercial vehicles. APQP and PPAP documentation where the programme requires it.
Typical Clients
Mahindra & Mahindra · Tata · Hyundai · Victor Reinz
MiningPrecision moulded components for abrasive, high-load extraction plant — not wear linings or conveyor rubber.
Products Supplied
Anti-Vibration Mounts, O-Rings, Bushes
Typical Clients
Shakti Mining Equipments
Oil & GasSealing rated to 250 °C for upstream and downstream service. NORSOK and API qualification is under way and targeted for 2027.
Find Oil & Gas Solutions
Pumps & ValvesShaft seals, valve seats and moulded diaphragms. Compound chosen against the pumped medium, not a catalogue default.
Products Supplied
Typical Clients
IDEX India
HVACAirtight compression under continuous low-amplitude vibration. Foam tape supplied as cut rolls to your width.
Products Supplied
Sponge & Foam, Extrusion Profiles, Gaskets
Typical Clients
Duct and panel fabricators
ElectricalInsulator head covers, cable grommets and switchgear bushings. Flame-retardant grades where UL 94 or FMVSS 302 applies.
Typical Clients
Starlite Lighting · Boost Electronics · Rohini Industries
MedicalBiocompatible silicone seals and tubing for diagnostic and laboratory equipment. We do not hold ISO 13485 or FDA registration.
Find Medical Solutions
WaterSealing rings to IS 5382 for water, gas and sewer mains, plus coupling gaskets and tank linings.
Products Supplied
Typical Clients
Treatment and distribution contractors
Weather- and UV-resistant parts for farm machinery and irrigation. Built for ozone attack under static strain in sunlight.
Products Supplied
Extrusion Profiles, Mounts, Grommets
Typical Clients
Farm machinery and irrigation OEMs
QUALITY & COMPLIANCE
What We Hold, and What We Do Not
One list, with the status of each certification stated on the badge rather than implied. A supplier who names that boundary is one you can plan around. Compound composition declarations are produced per part on request.
ISO 9001:2015
[Approved]Quality Management System
Certificate 09111526A, issued by Integral Certification Ltd, valid to 21 February 2027. The certified scope covers moulded rubber components; extension to the extruded and cellular lines is in hand.
Integral Certification Ltd · Certificate 09111526A · valid to 21 February 2027
IATF 16949:2016
[Upgrade in progress]Automotive Quality
Our quality management system is being upgraded to IATF 16949:2016, with certification targeted by the end of 2026. Automotive supply today runs against controlled drawing revisions with first-article approval and batch-level traceability.
Target end 2026
NORSOK M-710 / API
[Qualification in progress]Oil & Gas Elastomer Qualification
The qualification programme for hydrocarbon service is under way and is targeted for 2027. FKM compounds ship against published temperature and fluid-resistance data in the meantime.
Target 2027
ISO 14001:2015
[Upgrade in progress]Environmental Management
Not currently held. The plant is fully compliant with MIDC environmental and industrial norms, and material utilisation improved 20% after automation.
Target 2027
ISO 45001:2018
[Upgrade in progress]Occupational Health & Safety
Not currently held. Industrial-grade fire extinguishers, smoke detectors and ventilation throughout the plant, under MIDC industrial norms.
Target 2027
Scope: rubber moulded components — quality management, not a product approval. Read the certificate ›
TESTING & TRACEABILITY
Tested Here, or Tested at an Accredited Lab — Named Either Way
Every compound batch and every despatch lot is tested before it ships. Instruments sit on a scheduled calibration cycle, which is what makes a result traceable rather than merely recorded. Anything outside our bench goes to a NABL-accredited partner laboratory, on request.
| Test | Standard |
|---|---|
| Shore A hardness | ASTM D2240 / ISO 48-4 |
| Tensile & elongation at break | ASTM D412 / ISO 37 |
| Compression set | ASTM D395 / ISO 815-1 |
| Heat ageing, to 200 °C | ASTM D573 / ISO 188 |
| Cure curve, ODR rheometer | ISO 6502-2 |
| Specific gravity / filler dispersion | ASTM D297 / ISO 2781 |
| Dimensional conformity | ISO 3302-1 · M1–M4, E1–E3 |
| Test | Standard |
|---|---|
| Ozone resistance | ASTM D1149 / ISO 1431-1 |
| Fluid immersion ageing | ASTM D471 / ISO 1817 |
| Low-temperature brittleness & TR-10 | ASTM D2137 / D1329 |
| Abrasion · tear · rebound | ASTM D5963 / D624 / D2632 |
| Flammability | UL 94 / FMVSS 302 |
The 2026 Product Catalogue
Twelve production lines across eleven website categories, with material data, dimensional tables and application notes. One PDF, no login.
- Standard size series per line — AS568, ISO 3601 and metric
- Compound data sheets for all eight polymer families
- Profile section index for the extrusion line
- Application notes by industry
Get Instant Access
Enter your work email to receive the catalogue PDF.
No spam. Unsubscribe anytime. Your data is protected.
FREQUENTLY ASKED
Questions Buyers Ask Before the First Order
Send a drawing, a specification or a physical sample. Margo measures it, identifies the compound family and confirms feasibility, then returns a quotation and feasibility report within 48 hours. Margo produces in bulk against OEM schedules — minimum run from 10,000 pieces per part number, or quoted against the part where size or complexity sets the economics.
Yes. Compound, hardness and dimensions are set from your drawing or sample on every one of the eleven product lines. Mould and die tooling is designed and cut in-house from a CAD file, a section drawing or a worn part — no third-party toolroom in the loop.
Send the physical part. Margo measures it, identifies the compound family and quotes against the sample. A large share of Margo’s work starts as a worn component in an envelope rather than a CAD file, and reverse engineering is a standard route to a first order.
Name the fluid, the operating temperature and the load. Eight compounds are mixed in-house: AEM to 175 °C, FKM to 250 °C, silicone from −60 °C, EPDM for weather and steam, NBR for oil, neoprene, SBR and natural rubber. Margo’s engineers recommend the family at quotation stage.
Yes. O-rings are supplied to AS568, ISO 3601 and metric series, and to non-standard sections from a drawing. Dimensional conformity is held to ISO 3302-1 classes M1–M4 for moulded parts and E1–E3 for extruded sections; tolerance follows the section.
Quotation within 48 hours of an enquiry. Prototype 48 to 72 hours from an approved drawing, fitment samples inside two weeks, and production in three to four weeks standard or two weeks express. Nhava Sheva is 185 km from the plant, about three hours twenty by road.
Yes. Every despatch lot ships with hardness and dimensional release data, and compound batch, cure parameters and inspection results are retrievable per production batch. APQP and PPAP documentation is provided where the programme requires it. Ozone, fluid immersion and flammability testing goes to a NABL-accredited partner laboratory.
ISO 9001:2015, certificate 09111526A, issued by Integral Certification Ltd and valid to 21 February 2027. The certified scope covers moulded rubber components, with extension to the extruded and cellular lines in hand. Our quality management system is being upgraded to IATF 16949:2016, with certification targeted by the end of 2026.
Have a more specific technical question?
Ask Our EngineersRequest a Quotation
Share the part and the volume. Our engineering team replies within one business day, and a full quotation with a feasibility report follows inside 48 hours.
Direct Contact
PHONE
+91 96655 79276
Mon–Sat, 9am–6pm IST
EMAIL
info@margorubber.in
Reply within one business day
ADDRESS
Margo Rubber Products, SRNO. 4494/10, behind Furniture Stop, opposite Samarth Dies, Vilholi, Nashik, Maharashtra 422010, India
Our Quote Promise
- Acknowledgement within one business day
- Quotation and feasibility report inside 48 hours
- Compound recommended against your duty cycle
- Design-for-manufacture review at no cost